VENTS 150 Quiet-Mild Extra

• Innovative exhaust fan with stylish design for new comfort level in shower rooms, bathrooms, kitchens and other residential premises.
• Maximum air flow combined with low noise level provide the ideal microclimate.

• Mounting into ventilation shafts or connection to Ø 100, 125, 150 mm.

• Casing and impeller made of high-quality and durable UV-resistant plastic.
• Specially designed impeller aerodynamic profile provides high air flow and low noise.
• The compact design enables wall and ceiling mounting.
• The shortened spigot for mounting into a ventilation shaft or connection to Ø 100, 125, 150 mm air ducts.
• The fan is equipped with a specially designed back valve to prevent back flow and heat losses during the fan standby.

• The fan exhaust spigot incorporates specially designed air rectifiers to reduce air turbulence, increase air pressure and lower noise level.
• High ingress protection rating makes the fan the ideal solution for ventilation of a bathroom.
• The electronic components are protected with tight covers. 
• The fans VENTS 150 Quiet-Mild and VENTS 150 Quiet-Mild Extra are additionaly equipped with a special vibration absorbing sealer along the fan countour.

• Reliable ball bearing motor with low energy demand from 7.5 W.
• Maintenance-free bearings contain enough grease for 40 000 hrs non-stop operation.
• The motor rests on rubber anti-vibration connectors to ensure low-noise operation of the fan.

• The motor is equipped with overheating protection.
• Vents 150 Quiet-Mild model is equipped with a two speed motor Vents 150 Quiet-Mild Extra model is equipped with a two speed high-powered motor.

Operation modes for T modifications of VENTS 150 Quiet-Mild / VENTS 150 Quiet-Mild Extra models are selected by setting the switch.

Mode 1 (single-speed mode)

• The fan is turned off by default. The fan starts operating at the 1st speed when the switch is closed or one of the sensors is activated.

Mode 2 (single-speed mode)

• The fan is turned off by default. The fan starts operating at the 2nd speed when the switch is closed or the sensors are activated.

Mode 3 (two-speed mode)

• The fan operates at the 1st speed by default. The fan switches to the 2nd speed when the switch is closed or the sensors are activated.

Mode 4 (two-speed mode)

• The fan is turned off by default. The fan starts operating at the 1st speed when the switch isclosed and switches to the 2nd speed when the humidity sensor is activated.

Mode 5 (two-speed mode)

• The fan is turned off by default. The fan starts operating at the 1st speed when the switch is closed or when the humidity sensor is activated. If during the operation at the 1st speed the second even takes place. i.e. the switch is closed or the humidity sensor is activated, the fan switches to the 2nd speed.

Manual control:

• Manual control with a room light switch. The switch is not included in the delivery set.
• The fan is controlled by the built-in pull cord switch V. Not applied in case of ceiling mounting.
• Speed control is performed with a thyristor speed controller or with P2-1-300 speed switch (only for fans VENTS 150 Quiet-Mild and VENTS 150 Quiet-Mild Extra), see Electrical Accessories. Speed controllers can not be connected to the fans with T, TH, VT, VTH modification.

Automatic control:

• By the electronic control unit BU-1-60 (see Electrical Accessories). The control unit is supplied separately.
• By the timer T (the built-in turn-off delay timer enables the fan operation within 2 to 30 minutes after the fan switching off).
• By the humidity sensor and timer TH (if the humidity level in the room exceeds the sensor threshold within 60-90% the fan switches automatically on and operates until the humidity level drops to the standard level, after that the fan continues operating within the set time period and shuts down).
• By the motion sensor and timer TP (if motion is detected in the reach area, the fan is switched automatically and operates within the set time period from 2 to 30 min). Reach distance up to 4 m, the max. viewing angle 100°.

• Installation directly inside a ventilation shaft.
• Flexible air ducts may be used in case of remote location of the ventilation shaft. Connection of the air duct to the exhaust flange with a clamp.

• Wall mounting with screws.
• Suitable for ceiling mounting.