VENTS VKMI 250 Q

Print version Save in PDF format

Inline centrifugal fan in heat- and sound-insulated casing. Maximum capacity - 1190 m³/h.

Add to project

Add to compare

Description
Characteristics
Downloads
Dimensions
Additional diagrams
Legend

Description

APPLICATIONS
The new inline VKMI fans are enclosed in a specially designed sound-insulated casing, which ensures silent operation in combination with high aerodynamic characteristics. The fans are compatible with round air ducts from Ø 100 up to 315 mm and produce maximum air flow 1880 m³/h.	The VENTS VKMI fans are featured with wide capabilities and high performance of both axial and centrifugal fans, thus providing powerful air stream and high pressure. The fans are recommended as a component of the air handling systems for various commercial and industrial premises with high requirements to noise level, i.e. libraries, conference halls, educational institutions, kindergartens, etc.
DESIGN
The outer casing is made of polymer-coated steel. The inner casing perforation let sound waves pass through the holes and fall to the sound-absorbing layer at a specific angle. The casing is internally heat- and sound-insulated with 50 mm isover layer.	The specially perforated casing and sound-absorbing material provide sound attenuation in a broad frequency band. The inner casing and the impeller are made of high-quality durable plastic.

MOTOR
A centrifugal impeller with forward curved blades is powered by a single-phase external rotor motor. The motor is equipped with self-resetting overheating protection. Some standard sizes are available with a high-powered motor, see modification VKMI S.	The motor is equipped with ball bearings for a long service life designed for at least 40 000 operating hours. For precise features, safe operation and low noise, each impeller is dynamically balanced while assembly. Motor protection rating is IP 44.
SPEED CONTROL
Smooth or step speed control with a thyristor or autotransformer speed controller.	Several fans may be connected to one speed controller provided that the total power and operating current do not exceed the rated speed controller parameters.
MOUNTING
The fans are designed for inline mounting inside an air duct of matching air duct diameter, in any point of the ventilation system and at any angle.	The fan can be supplied with fixing brackets for fastening to the wall (K option).
The fan with electronic temperature and control module (U option)
The ideal solution for ventilation of the premises requiring permanent temperature control, i.e. greenhouses.	The fan with the electronic temperature and speed control module provides automatic control of the motor speed (air capacity) depending on air temperature in the air duct or in the room.
The front panel of the electronic module has the following control knobs: speed control knob for setting the motor speed; thermostat control knob for setting the temperature set point; thermostat indicator light.	The fan is available in two modifications: with the temperature sensor integrated inside the fan air duct (U/U1 option); with the external temperature sensor fixed on the cable, 4 m long (Un / U1n).
Control logic of the fan with the electronic temperature and speed control module
Set the desired air temperature (thermostat set point) by turning the thermostat control knob. Set the required minimum impeller speed (air flow) by turning the speed control knob. The motor switches to maximum speed (maximum air flow) as the temperature reaches and exceeds the set temperature set point.	The motor switches to the pre-set lower speed as the temperature drops down below the temperature set point. To avoid frequent motor speed switches when the air temperature in the duct is equal to the set temperature point, the speed switch delay is activated.
There are two switch delay patterns for various cases:
The temperature sensor-based switch delay (U option): the motor switches to higher speed as the air temperature exceeds 2°C above the set thermostat set point. The motor revers to the pre-set lower speed as the air temperature drops below the thermostat set point. This pattern is used to keep air temperature to within 2°C. In this case the motor speed switches are rare.	The timer-based switch delay (U1 option): as the air temperature exceeds the set thermostat set point, the motor switches to higher speed and the switch delay timer is activated for 5 min. The motor reverts to lower speed as the air temperature drops down below the thermostat set point and only after 5 minuts timer countdown. This pattern is used for exact air temperature control. The speed switches for the fan with U1 option are more frequent as compared to the operating logic of the fan with U option, however the minimum operating cycle at one speed is 5 minutes.

Characteristics

Parameter	VKMI 250 Q	Measurement unit
Highpowered motor	no	-
Low-powered motor	no	-
Voltage	230	V
Frequency	50	Hz
Sound pressure level at 3 m distance	46	dBА
Power consumption	158	W
RPM	2315	min^-1
Maximum air capacity	1190	m³/h
Current	0.69	A
Max. transported air temperature	-25 +50	°С
Protection rating	IP X4	-
Design	centrifugal	-
Duct diameter	250	mm
Weight	13.4	kg
Sound- and heat-insulated casing	yes	-
Casing material	polymer coated steel	-
SEC Class	-	-
Duct	for round air ducts	-
Type	supply and exhaust	-
Mounting	Inline	-

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit
A	625	mm
∅D	248	mm
B	410	mm
H	320	mm
C	389	mm
h	250	mm
c	250	mm

Additional diagrams

Sound-power level		Octave-frequency band [Hz]
	Hz	General	63	125	250	500	1000	2000	4000	8000
L_wA to inlet	dBA	68	46	57	60	65	62	58	60	54
L_wA to outlet	dBA	64	37	50	54	55	57	55	58	50
L_wA to environment	dBA	51	37	48	44	40	31	33	43	38

Legend

Series fan	Air duct diameter, mm	Options
VENTS VKMI	100; 125; 150; 160; 200; 250; 315	U – speed controller with electronic thermostat and temperature sensor integrated into the air duct. Equipped with power cord and IEC C14 electric plug. Temperature-based operation logic. U1 – speed controller with electronic thermostat and temperature sensor integrated into the air duct. Equipped with power cord and IEC C14 electric plug. Timer-based operation logic. Un – speed controller with electronic thermostat and external temperature sensor fixed on 4 m cable. Equipped with power cord and IEC C14 electric plug. Temperature-based operation logic. U1n – speed controller with electronic thermostat and external temperature sensor fixed on 4 m cable. Equipped with power cord and IEC C14 electric plug. Timer-based operation logic. P – built-in smooth speed controller and power cord with IEC C14 electric plug. R – power cord with IEC C14 electric plug. Q – low-powered motor. S – high-powered motor. K – versatile fixing bracket.

ErP data
Overall efficiency	η,[%]
Measurement category	MC
Efficiency category	EC
Efficiency grade	N
Variable speed drive	VSD
Power	[kW]
Current	[A]
Air flow	[m³/h]
Static pressure	[Pa]
Speed	[n/min^-1]
Specific ratio	SR