VENTS MF Series

Print version Save in PDF format

Low-noise and energ saving axial fan for exhaust ventilation with air capacity up to 255 m³/h.

Series of products

VENTS 100 MF

VENTS 100 MF (220-240 V/60 Hz)

VENTS 100 MF 12

VENTS 125 MF

VENTS 125 MF (220-240 V/60 Hz)

VENTS 150 MF

VENTS 100 MFVENTS 100 MF (220-240 V/60 Hz)VENTS 100 MF 12

VENTS 125 MF VENTS 125 MF (220-240 V/60 Hz)VENTS 150 MF

Description
Modifications
Capacity diagram
Downloads
Certificates
Designation key

Description

APPLICATIONS
Continuous or periodic exhaust ventilation of bathroom, showers, kitchens and other utility spaces. Ventilation of premises with high noise level limitations.	Mounting into ventilation shafts or connection to Ø100, 125 and 150 mm air ducts.
DESIGN
The casing and the impeller are made of highquality durable ABS plastic, UV resistant. Specially designed impeller aerodynamic profile provides high air capacity and low noise.	The fan is equipped with a back valve to prevent back flow and heat losses during the fan standby. The fan exhaust spigot incorporates specially designed air rectifiers to reduce air turbulence, increase air pressure and lower noise level.
MOTOR
Low energy demand from 8 W due to new high-efficient motor. Protection rating IP 44.	Designed for continuous operation and requires no maintenance. Motor equipped with overheating protection.
CONTROL
Manual control: Manual control with a room light switch. The switch is not included into delivery set. The fan is controlled by the built-in pull cord switch V. Not applied in case of ceiling mounting. Speed control is possible through a thyristor\speed controller (see Electrical Accessories). Several fans may connected to the same controller. Speed controllers can not be connected to the fans with T, TH, TP, VT, VTH modification.	Automatic: By the electronic control unit BU-1-60. The control unit is supplied separately. By the timer T (the built-in run-out timer enables the fan operation within 2 to 30 minutes after the fan switching off). By the humidity sensor and timer TH (if the humidity level in the room exceeds the sensor threshold adjustable value within 60-90% the fan switches automatically on and operates until the humidity level drops to the standard level, after that the fan continues operating within the time period according to the timer setting, then shuts down).
MOUNTING FEATURES
The fan is mounted directly into the ventilation shaft. Flexible duct application is recommended in case of remote location of the ventilation shaft. The air duct is connected to the fan exhaust flange through a clamp.	Fixed to wall by self-tapping screws. Suitable for ceiling mounting.
MOUNTING EXAMPLE

Modifications

Modification name

VENTS 100 MF 12

VENTS 100 MF

VENTS 125 MF VT (220-240 V/60 Hz)

VENTS 125 MF (220-240 V/60 Hz)

VENTS 125 MF V

VENTS 100 V (220-240 V/60 Hz)

VENTS 125 MF T

VENTS 100 T (220-240 V/60 Hz)

VENTS 150 MF V

VENTS 100 MF VTH 12

VENTS 100 MF BTH

VENTS 125 MF TH (220-240 V/60 Hz)

VENTS 100 MF TH 12

VENTS 100 MF TH

VENTS 150 MF T

VENTS 100 MF L 12

VENTS 100 MF L

VENTS 125 MF VTH (220-240 V/60 Hz)

VENTS 125 MF L (220-240 V/60 Hz)

VENTS 125 MF VT

VENTS 100 VT (220-240 V/60 Hz)

VENTS 125 MF T1

VENTS 100 T1 (220-240 V/60 Hz)

VENTS 150 MF VT

VENTS 125 MF

VENTS 100 MF (220-240 V/60 Hz)

VENTS 150 MF T1

VENTS 125 MF V (220-240 V/60 Hz)

VENTS 100 MF V 12

VENTS 100 MF B

VENTS 125 MF T (220-240 V/60 Hz)

VENTS 100 MF T 12

VENTS 100 MF T

VENTS 150 MF

VENTS 100 VTH (220-240 V/60 Hz)

VENTS 125 MF VTH

VENTS 125 MF TH

VENTS 100 TH (220-240 V/60 Hz)

VENTS 150 MF VTH

VENTS 125 MF L

VENTS 100 MF L (220-240 V/60 Hz)

VENTS 150 MF TH

VENTS 100 MF VT 12

VENTS 100 MF BT

VENTS 125 MF T1 (220-240 V/60 Hz)

VENTS 100 MF T1 12

VENTS 100 MF T1

VENTS 150 MF L

No extra functions

Ball bearing motor

Timer

Humidity sensor

Pull-cord switch

Capacity diagram

Selection method:
Air flow:
Pressure:

Operating point

Air flow: --
Pressure: ---

Downloads

Certificates

<p>
Mark of conformity to the European Quality Standards and Electrical Safety issued by Association for Technical Inspection (Technischer Überwachungsverein, Germany).</p>

Mark of conformity to the European Quality Standards and Electrical Safety issued by Association for Technical Inspection (Technischer Überwachungsverein, Germany).

Mark of conformity to the Polish Quality Standards and electrical safety issued by PCBC (Polish center for testing and certification).

Mark of conformity to the Slovak Quality Standards and electrical safety issued by EVPU (Slovakia).

Mark of conformity to the Ukrainian Quality Standards and electrical safety issued by UkrTEST.

<p>
Mark of conformity of the goods subject to obligatory certification in DSTR system as well as technical norms and standards acting in Russian Federation. Confirmed by the RosTEST certificates (Moscow). </p>

Mark of conformity of the goods subject to obligatory certification in DSTR system as well as technical norms and standards acting in Russian Federation. Confirmed by the RosTEST certificates (Moscow).

Insulation class: double insulation.

Equipment protection rating.

Designation key

PICTURE SYMBOL	DESIGNATION	MODIFICATION DESCRIPTION
	MF L	The motor is equipped with bal bearings for long service life (appr. 40 thousand hours) and fan mounting at any angle. The bearings are maintenance-free and contain enough grease for the entire operating period.
	MF T	Off-delay timer modification with operating time from 2 to 30 min.
	MF T1	Modification with turn-on delay timer (adjustable from 0 to 2 minutes) and off-delay timer (adjustable from 2 to 30 minutes).
	MF TH	Off-delay timer modification with the operating time from 2 to 30 min and humidity sensor with threshold from 60 to 90%.
	MF V	pull-cord switch modification.
	MF VT	Modification with pull-cord switch and off-delay timer with operating time from 2 to 30 min.
	MF VTH	Modification with pullcord switch, offdelay timer with operating time from 2 to 30 min and humidity sensor with threshold from 60 to 90%.