VENTS KSA 315-4E

Print version Save in PDF format

Centrifugal fan in heat-and sound-insulated casing. Maximum capacity - 2140 m³/h.

Add to project

Add to compare

Description
Characteristics
Downloads
Dimensions
Additional diagrams
Designation key

Description

APPLICATIONS
KSA fan design enables their application in supply and exhaust ventilation systems for the premises with high noise level requirements.	Suitable for connection with Ø 100, 125, 150, 160 and 200 mm round ducts.
DESIGN
The fan casing is made of aluzinс.	Heat- and sound-insulating layer is made of polystyrene foam.
MOTOR
The impeller with forward curved blades made of galvanized steel is powered by 2- or 4-pole external rotor asynchronous motor. The motor is equipped with the ball bearings for long service life.	For precise features, safe operation and low noise, each impeller is dynamically balanced while assembly. Motor protection rating IP44.
SPEED CONTROL
Smooth or step speed control with a thyristor or autotransformer speed controller.	Several fans may be connected to one speed controller provided that the total power and operating current do not exceed the rated speed controller parameters.
MOUNTING
Connection pipes have round section. The fan basic delivery set includes a power cord without an electrical plug.	Electric connection and mounting shall be performed in compliance with the operation manual and wiring diagram.
THE FAN WITH ELECTRONIC TEMPERATURE AND CONTROL MODULE (U OPTION)
The ideal solution for ventilation of the premises requiring permanent temperature control, i.e. greenhouses.	The fan with the electronic temperature and speed control module provides automatic control of the motor speed (air flow) depending on air temperature in the air duct or in the room.
The front panel of the electronic module has the following control knobs: speed control knob for setting the motor speed; thermostat control knob for setting the temperature set point; thermostat indicator light.	The fan is available in two modifications: with the temperature sensor integrated inside the fan air duct (U/U1/U2 option); with the external temperature sensor fixed on the cable, 4 m long (Un/U1n/U2n).
Control logic of the fan with the electronic temperature and speed control module
Set the desired air temperature (thermostat set point) by turning the thermostat control knob. Set the required minimum impeller speed (air flow) by turning the speed control knob. The motor switches to maximum speed (maximum air flow) as the temperature reaches and exceeds the set temperature set point.	The motor switches to the pre-set lower speed as the temperature drops down below the temperature set point. To avoid frequent motor speed switches when the air temperature in the duct is equal to the set temperature point, the speed switch delay is activated.
There are three switch delay patterns for various cases:
The temperature sensor-based switch delay (U option): the motor switches to higher speed as the air temperature exceeds 2 °C above the set thermostat set point. The motor revers to the preset lower speed as the air temperature drops below the thermostat set point. This pattern is used to keep air temperature to within 2 °C. In this case the motor speed switches are rare. The timer-based switch delay (U1 option): as the air temperature exceeds the set thermostat set point, the motor switches to higher speed and the switch delay timer is activated for 5 min. The motor reverts to lower speed as the air temperature drops down below the thermostat set point and only after 5 minuts timer countdown. This pattern is used for exact air temperature control. The speed switches for the fan with U1 option are more frequent as compared to the operating logic of the fan with U option, however the minimum operating cycle at one speed is 5 minutes. Switching ON/OFF by a temperature sensor (U2 option): when the air temperature exceeds by 2 °C the thermostat actuation set point, the fan starts operating at the set speed. The fan switches off when the temperature drops below the temperature set point.

VENTS KSA fan greenhouse ventilation example

Characteristics

Parameter	KSA 315-4E	Measurement unit
Phase	1	˜
Voltage	230	V
Frequency	50	Hz
Sound pressure level at 3 m distance	44	dBА
Power consumption	570	W
RPM	1325	min^-1
Maximum air capacity	2140	m³/h
Current	2.48	A
Max. transported air temperature	-40 +55	°С
Protection rating	IP X4	-
Design	centrifugal	-
Weight	17	kg
Duct diameter	315	mm
Number of poles	4	-
Sound- and heat-insulated casing	yes	-
Casing material	aluzinc	-
SEC Class	-	-
Duct	for round air ducts	-
Type	supply and exhaust	-
Mounting	Inline	-

Files archieve

Downloads

Dimensions

Characteristics

Parameter	Value	Measurement unit
∅D	314	mm
B	392	mm
H	495	mm
Р	48	mm
L	535	mm

Additional diagrams

Sound-power level		Octave-frequency band [Hz]
	Hz	General	63	125	250	500	1000	2000	4000	8000
L_wA to inlet	dBA	45	41	42	39	29	25	25	27	25
L_wA to outlet	dBA	48	43	46	40	35	26	30	20	19
L_wA to environment	dBA	44	36	39	31	25	22	25	18	17

Designation key

Series	Spigot diameter	Polarity	Phase	Options
VENTS KSA	100; 125; 150; 160; 200	2, 4	Е: single phase	U: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Temperature-based operation logic. Un: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Temperature-based operation logic. U1: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Timer-based operation logic. U1n: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Timer-based operation logic. U2: speed controller with an electronic thermostat and a temperature sensor integrated inside an air duct. Temperature-based switching on/off. U2n: speed controller with an electronic thermostat and a temperature sensor fixed on a 4-meter cable. Temperature-based switching on/off. R1: power cord with a mains plug. P: integrated smooth speed controller.